How To Install Backup Camera 2006 F150

How To Install A Backup Camera On A Ford F150

F-150 backup mirror kit CS-FTR-F35. This kit will only work with trucks with an existing xvi-pin mirror connector. If you lot do non have a connector, it is best to use kit CS-FTRa-332

Preparing The Expanse

Footstep i

Remove the rear view mirror glass prior to starting the project. We recommend working with a professional. The glass breaks very easily and nigh auto glass companies can do this for free.

Step 2

Use line-fishing line to remove the Ford emblem from the tailgate.

Stride 3

Locate the center hole with your finger. Use a razor knife to cut away tape from center hole every bit a square.

Step 4

Locate the square holes to the left and right of the center hole. They are currently behind the record. These are not the holes that the decal fits into. Cutting the tape abroad from these holes in a square shape.

Step 5

Employ the kit'south two included body nut clips and push them into the left and right side foursquare openings.

Installing The Wiring

Stride half dozen

Fish the kit'southward included camera cable through the tailgate and out the opening in the lesser of the Ford F150.

Step vii

Pull the cord all the fashion through and connect the emblem to the trunk nut clips.

Stride 8

Spike the emblem to the tailgate using the kit's included body bolts.

Stride 9

Open up the tailgate upward and lay apartment. Fish the wire through the opening in the back of the bed. The opening is located between the bed of the truck and the tailgate.

Connecting The Camera

Step 10

Carefully connect the photographic camera to the chassis harness. It is keyed and only goes together i way. Push information technology in every bit tight as you tin to ensure a good connection.

Pace 11

Cut off the alternate power supply sure and tuck it within the harness. From hither we are going to brand all of the connections in the cab.

Important Note: Remember that the red wire at the rear of the harness is only to be used if you lot practice not want to locate a power source inside the cab. Both red wires are live when power is applied.

Step 12

Route the chassis harness forth the frame and come upwardly into the engine compartment side by side to the brake booster.

Step 13

Push the harness through the main wiring grommet by putting a slit in the nipple at the acme of the grommet.

Step 14

Pare dorsum the loom and feed the wire through the grommet. Be conscientious not to damage the RCA end.

Step 15

Cut the excess loom to fit. The harness should pull nicely through the indented pigsty in grommet.

Step 16

Remove the overhead trim panel with a difficult tug or tool and disconnect the wires.

Stride 17

Remove the terminal lock from the connector and pull off the confront of the connector.

Installing The Camera Wiring

Pace 18

Insert yellow and black video wires into connector: yellow to pin 8 and black to pivot 16. Replace the last lock.

Of import Note: If at that place is no wire in pin ii, y'all will likewise demand to add the CAN passenger vehicle terminal as shown in instructions in kit.

Step 19

Carefully cut away and remove the wire capsule then that the video wires tin be paired with the chief harness. The video wires will be covered using the blackness trim cover included in the backup camera kit.

Step twenty

Remove the a-pillar embrace with a tug. If you have a handle, remove the two bolts before tugging.

Step 21

Remove the dash-side panel and route the RCA and camera power/footing wires from the kit up along the a-pillar rail.

Stride 22

Connect the RCA to the mirror RCA input. This tin can be tucked along the headliner and the drinking glass in the a-pillar.

Step 23

Route the ability and footing wires to the upper eye console area.

Step 24

Locate the reverse-activated power wire in the mirror pine: bluish/white wire in pivot ix.

Pace 25

Use the kit's tap splice to connect the camera red wire to the contrary-activated power wire in the harness.

Step 26

Connect the photographic camera back to the black wire in grounded pin 4 of the factory connect. Splicing, soldering, and compress wrapping your connections is recommended.

The Final Touches

Pace 27

Tuck the camera power/basis wires betwixt the headline and glass.

Step 28

Secure the wires against the a-colonnade using stiff tape. Make sure the airbag is clear. Reinstall the a-pillar cover.

Pace 29

Plug in the mirror and install on the wedge. If you want to examination first (always a good idea), push it on only far plenty so it is on temporarily.

Step 30

Exam the camera by starting the truck and placing it in reverse. You should see the mirror light upward with a video image.

Step 31

Push wires back in overhead and put trim panel back in the headliner. Putting the headliner in identify may take a few tries and a few good pushes.

Step 31

Snap the tailgate emblem on the housing.

Relish Your New F150 Fill-in Camera

Congratulations! You've just installed a brand new backup camera on your Ford F150. At present y'all can savour the added convenience and safety a backup photographic camera provides when parking or reversing.

If y'all need farther caption of installation instructions, view your fill-in photographic camera kit's instruction manual, or check out the video below:

Source: https://camerasource.com/blog/how-to-install-a-backup-camera-on-a-ford-f150/

Posted by: cifuentestheigh1992.blogspot.com

Share this post